IDE and SATA are different types of interfaces to connect storage devices (like hard drives) to a computer's system bus. SATA stands for Serial Advanced Technology Attachment (or Serial ATA) and IDE is also called Parallel ATAor PATA. SATA is the newer standard and SATA drives are faster than PATA (IDE) drives. For many years ATA provided the most common and the least expensive interface for this application. But by the beginning of 2007, SATA had largely replaced IDE in all new systems.
The ATA interface (ATA stands for AT attachment where "AT" refers to IBM's PC/AT for which it was originally built) evolved in stages from Western Digital's original Integrated Drive Electronics (IDE) interface. After the introduction of Serial ATA in 2003, the original ATA was retroactively renamed Parallel ATA.
IDE | SATA |
|---|
| Stands for / AKA | IDE: Integrated Drive Electronics / PATA: Parallel Advanced Technology Attachment | Serial Advanced Technology Attachment Serial ATA |
| Lineage | Superseded by SATA | Supersedes Parallel ATA (PATA) aka IDE |
| Year Created | 1986 | 2003 |
| Hot plugging (add/remove component while the computer is running) | IDE interface does not support hot plugging | SATA interface supports hot plugging |
| Speed | data transfers at the rate of up to 133Mb/sec | data transfers at the rate of 150Mb/sec to 6Gbits/sec |
| Data cable | Ribbon-like, wide, can be up to 18 inches long | Narrow, can be up to 39 inches long |
| Advantages | Maximum compatibility | SATA cables are also smaller in size than a PATA cable, allowing for increased airflow inside the computer case and decreased heat build up. This can help improve the overall life of a computer. |
| Disadvantages | Lacks support for new technology such as native command queuing and hot-plugging hard drives | 1. SATA hard drives will sometimes require a specific driver to be loaded to a computer when installing an operating system 2.SATA is that the cable allows for only one SATA hard drive to be connected at a time. Whereas a PATA cable allows for hookin |
| Jumpers | In a computer system, it's possible to have more than one harddrive. To connect multiple IDE drives, you need to chain the ribbon cables from one to the next. The computer system has no idea which is the main drive, from which to load the OS. | SATA drives don't use jumpers. Each drive connects directly to the motherboard. To set the primary drive, you can access the settings from the computers BIOS (special software that runs when you start the computer). |
Differences in Cables and Connectors
Hard drives need a cable/connection for data and one for power. Parallel ATA only allows data cable lengths up to 18 in (457 mm) while SATA allows cable lengths up to 1 m (3.28 ft). eSATA cables can be 2 m in length.
IDE consists of a 40-pin connector attached to a ribbon cable. 80-pin connectors were also introduced later. The connectors are black in a 40-pin connector while in an 80-pin connector, they come in 3 colors: blue - controller, gray - slave drive, and black - master drive. Each cable has two or three connectors, one connector is attached to the interface that connects to the computer system (mother board) and the others are connected to the drives.
SATA consists of an 8 mm wide wafer connector on each end and the cable has a 7-pin connector, 3 grounds and 4 active data lines in two pairs. It has the facility to attach only one drive and so Serial ATA does away with Master/Slave configurations.
Adapters and Integrated Motherboards
You can buy integrated motherboards that allow a computer to use both SATA and IDE hard drives. However, only one of the two may be used at any given time and both cannot be used simultaneously. Adapters are also available that allow an IDE drive to be used with a SATA motherboard and vice versa. These IDE/SATA adapters mask the underlying hard drive and simulate its functioning to match the expectations of the computer's motherboard. They usually cost less than $15.
Variants
Two variant of SATA - eSATA and eSATAp - are available. eSATA is meant for external connectivity. eSATA cannot supply power from the motherboard to the hard drive. In order to overcome this limitation, eSATAp drives were introduced. eSATAp port combines the strength of both eSATA (high speed) and USB(compatibility) into a single port.
Operation
Speed
Data transfer speed for IDE ranges from 5MB/sec up to 133MB/sec (ATA100/133). The parallel wire transfer mode reached its limit with the speed of 133
MB/sec. SATA took off where ATA stopped as far as speed is concerned. The first generation of SATA was 1.2 Gbit/s (150 MB/s; note that MB is mega
bytes and Gb is giga
bits) similar to PATA/133. Today the third generation of SATA (3.0) (released on May 27, 2009), 6 Gbit/s hard drives and motherboards are being used.
Air flow
The wide wire in IDE cables caused airflow problems inside the case. The narrower SATA cable allows free airflow inside the case.
Hot Plugging
SATA drives have an additional feature of Hot plugging which mean that even as the computer is running drives can be removed or added.
Power Consumption
PATA (IDE) drives need 5 volts and 12 volts in desktop form factor.
SATA drives use 5 & 12 volts & 'can' include 3 volts as well
but nearly all current disk drives do not use the 3.3 V line.
Master/Slave Configuration
SATA has also done away with the master/slave configuration (technically, device 0and device 1) used in IDE drives. Unlike PATA, there can be only drive attached to the motherboard when using SATA drives.
Posts
